DC12V-36 500W JYQD_V6.3E1 Brushless Motor PWM Controller w/ Balanced Hall Board

Description

Home
Arduino
Module
Sensor
Chips
About Us
DC Brushless Motor Controller
Features:
Drive plate type: JYQD_V6.3E1
Voltage range: 12V-36V
Peak current: 20A
Drive power: ≤ 500W (related working voltage)
Size: 63x43x17mm
Speed control function: voltage speed regulation or single chip
microcomputer control PWM speed regulation
Control terminal connection:
1. GND
2. VR speed control port connection method can be controlled by voltage regulation control or PWM control speed voltage regulation can be adjusted by the adjustable resistance (20K 3 pin bit VR port side of the port side of the 5V port to connect to the GND port through the regulation of voltage control)
3. ZF positive reverse port connection method to connect 5V a direction to the direction of GND
4. Singnal speed pulse output port output of a circle of pulse = motor pole number x 3
5. 5V control terminal 5V voltage output port
Power end connection:
1. VCC power positive input port (12V-36V)
2. GND power input port
3. MC brushless DC motor without a sense / no Holzer motor three line W
4. MB brushless DC motor without a sense / no Holzer motor three line V
5. MA brushless DC motor without a sense / no Holzer motor three line U
Package Included:
1 x 500W DC 12V-36V Brushless Motor PWM Control Controller Balanced BLDC Driver Board
DC Brushless Motor Controller Hall Driver
Compared with the previous version:
1. E2 Effectively prevent damage to the power control board problem-
second E2 optimized power control circuit, improved motor torque output
3. E2 Increases the safety distance of the power leads, makes the surgery of the wire easier and Eliminates the short circuit Caused by the safety distance of the previous version
4. E2 fixed screw hole made a fully shielded design to solve the problem-of shortcircuit Caused by the previous version of the fight to screw
5 E2 in the application of the continuation of all the features of the previous version, can use E2 instead of E1 version
Specification:
operating voltage: 12V-36V
operating Current: <= 15A
Driver Power: <= 500W
Speed ​​Voltage: 0.1V-5V
Operating Temperature: -40-85 ° C
Humidity: 90% RH
Stable protection: Yes
Enable Control: Yes
Over-current protection: Yes
Steering control: Yes
Speed ​​control signal: Yes
Size: 63 * 42 * 17mm (L * W * H); Sample size 3mm,
length: fixing hole center distance 57mm;
width: fixed hole center distance 36.5mm
Power terminal Out:
VCC (positive power supply)
GND (negative one)
MC (motor phases W)
MB (motor phases V)
MA (motor phase U)
Set for the control side:
[GND] control terminal ground
[VR] the governor end 0-5V (corresponding to 10% of motor speed -100%)
[ZF] reversing control (connected to 5V or ground can charge the motor rotation direction)
[M] tachometer pulse output(depending on the number of motor poles corresponding to the number of pulse per revolution of the output number)
[EL] enable control terminal(connected to 5V ot ground running then 5V, grounding the motor stops)
[5V] 5V control terminal
HALL for the hall terminals:
[5V] Hall power positive
[Ha] Hall signal
[Hb] Hall signal
[Hc] Hall Signal
[GND] Hall negative
Wiring:
Control terminal for SET:
1. The motor speed control wiring methods: available potentiometer system speed can also be connected to the MCU control, when the potentiometer control wiring, the potentiometer middle pin is connected to VR speed port, potentiometer connected to both ends of 5V and GND terminal voltage more high speed faster.
2. Motor steering control wiring methods： you can switch control can also be connected to the MCU control, to GND in one direction, then in one direction 5V.
3. Pulse speed signal: high and low output . IC can not understand the information with the customer request.
Hall signal inputs for hall:
Wiring diagram is shown, one corresponding to the HA, HB,HC and on the motor, 5V power supply connected to the motor hal signals positive, GND power supply negative signal to the motor hall.
Note: Due to different motor manufacturers to make the hall of hall line order does not necessarily follow the line on the board to match the sequence, need to be adjusted, please parents who pay attention! If the line sequence wrong, does not boot properly, current, or start other phenomena not open, forced to use the drive plate will burn!!!
Motor driver board 12-36V DC power input , VCC positive power supply,GND power supply is negative.
Electrical wiring methods: Brushless DC motor for the three lines, corresponding MA/U,MB/V,MC/W
Tips: If you use less than 60W, without additional heat sink , be sure to add more than 60W
heatsink fins drive efficiency without lowering the temperature is too high will shine into permanent damage! The size of the heat sink may be a bad environment based work(recommended cooling surface area greater than 200 square centimeters)!When installing the heat sink ,must pay attention to the back of the module 6 MOS pipe insulation, no insulation, it will be adhered to drive plate permanently damaged! Proposes to add insulation films, both sides of the insulating sheet plus thermal grease!
Package Includes:
1 x 12-36V 500W Brushless Motor Controler
Payment
Shipping
Refund
Payment
We accept PayPal only.
But we only
Accept
your
Ebay Address
,Please Make sure it's 100% right.
Payment must be received in 5 business days of auction closing.
Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
Shipping
Fill your shipping info
Refund
All package need to
wait 30 days
(US only n
eed 7-10 days)
,
Please take care it.Less than 30 days,we can't take a refund
.
If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.